您当前位置:首页 > 设备频道 > 供求信息 > 供应信息 > 江苏设备网 > 详情

全自动辊压筋电缆桥架成型机组

0
产品简介

设备技术要求

Equipment technical requirements

设备技术条件:

Equipment technical conditions:

设备占地面积: 35×3.5×5(长×宽×高)米。

Equipment cover an area of an area: 35 * 3.5 * 5 meters (length x width x height).

设备进料方向:左进右出。

Equipment feed direction: left to right.

电压参数380,50Hz,3相。

Voltage parameter 380, 50 Hz, 3 phase.

气源:流量为0.5m3/分钟;

Source: the flow of 0.5 m3 / min;

压力为0-0.7MPa。

 

Pressure to 0-0.7 MPa.

液压油:46#液压油。

The hydraulic oil: 46 # hydraulic oil.

齿轮油:18#双曲线齿轮油。

Gear oil: 18 # hyperbolic gear oil.

设备主要技术参数

 

Equipment main technical parameters

轧制带钢宽度:200—950 mm

Rolling steel strip width: 200-950 mm

轧制带钢厚度:0.6~2.0 mm

Rolling steel strip thickness: 0.6 ~ 2.0 mm

轧制带钢材质:Q235冷轧带钢

Rolling steel strip material: Q235 cold-rolled strip steel

在线冲孔、生产速度:2-6m/分钟(根据产品长度及冲孔的数量决定)

online punching.production speed: 2-6 m/min (determined according to the length.the number of punching products)

主机成型速度:10-12m/分钟

The host molding speed: 10 to 12 m/min

轧制工件长度:2000—12000 mm

Rolling workpiece length: 2000-12000 mm

电机防爆等级ExdIICT4

ExdIICT4 explosion-proof motor level

电机防护等级IP55

Motor protection grade IP55

设备装机总容量:约35KW。

Equipment installed gross capacity: about 35 kw.

轧制产品范围

The product range of rolling

本冲压成型机组可以轧制最大厚度为2.0mm槽盒式电缆桥架,产品宽度从100至600mm,高度从50至150mm之间不同规格的钢质电缆桥架产品。

 

The stamping forming unit can be rolling thickness of 2.0 mm slot box type cable tray, products from 100 to 600 mm in width, height from 50 to 150 mm between different specifications of steel cable tray products.

供货及服务范围

The scope of supply.services

本条款规定了合同设备的供货范围(见表一),卖方保证所提供设备为全新的、先进的、成熟的、完整的和安全可靠的,且设备的技术性能、功能符合技术条件的要求。

The provisions of this clause of the contract equipment in the scope of supply (see chart 1), the seller guarantees that the equipment for new, advanced, mature.complete,.safe.reliable,.the equipment of the technical performance.function accord with the requirement of technical conditions.

卖方确保供货范围完整,以能满足用户安装、运行要求为原则,在技术规范中涉及的供货要求也作为本供货范围的补安装、调试、运行中发现缺项由卖方补充。

The seller to ensure that the complete scope of supply, in order to meet the demand of users to install.run for the principle, supply requirements are also involved in the technical specification of the scope of supply for installation, debugging.operation of found missing items added by the seller.

成型工艺

Molding process

被动放料..校平..冲孔(冲连接孔)..切断..成型.-出料

 

Passive feeding, leveling, punching rushed connection (hole) - cutting - forming - discharging

About Us - 关于我们 - 服务列表 - 付费指导 - 媒体合作 - 广告服务 - 版权声明 - 联系我们 - 网站地图 - 常见问题 - 友情链接
Copyright©2014安装信息网 www.zgazxxw.com. All rights reserved.
服务热线:4000-293-296 邮箱:zgazxxw@126.com 豫ICP备18030500号-4
未经过本站允许,请勿将本站内容传播或复制
安全联盟认证